Affiliate disclosure: This article contains affiliate links. We may earn a commission if you purchase through them, at no extra cost to you.
A timber skid foundation is the fastest and cheapest way to get most garden sheds off the ground; paving slabs suit medium sheds on slightly uneven gardens; poured concrete is only really worth it under large workshop-style sheds carrying serious weight. Whichever you choose, the job of any shed foundation is the same: keep the building level, spread its weight evenly, and separate timber from damp soil so it doesn’t rot from below.
Key takeaways
- Never build directly on grass or soil: sheds sink, twist and rot within a couple of seasons without a proper base.
- Timber skids on compacted gravel are the easiest DIY option and allow future re-levelling.
- Paving slabs are a good middle ground: more stable than gravel, far less work and cost than concrete.
- Concrete suits large sheds and heavy workshops but is permanent and the most labour-intensive.
- Compaction and levelling matter more than the material you pick; a level, well-drained base prevents sagging floors and sticky doors.
Why your shed foundation matters more than the shed
The foundation is the most important part of your shed that nobody sees. Get it wrong and you’ll see sagging floors, doors that stick, water pooling inside and a structure that deteriorates years before it should. Even a modest 8×10 shed loaded with tools can weigh over 3,000 pounds (roughly 1,360 kg), and that weight needs to be spread across stable ground or the shed will settle unevenly over time, as explained in the Shed Foundation Guide from Shed Build Planner.
Moisture is the second enemy. Timber in direct contact with soil soaks up water through capillary action, inviting rot and insect damage. Every foundation type solves this differently, but the goal is always an air gap or moisture barrier between the ground and your framing lumber.
It’s also worth being honest about what happens if you skip a base entirely. UK shed retailer Opal Retail describes a common story: sheds installed straight onto a lawn start sinking within a season, grass grows up through gaps in the floor, and in some gardens animals dig underneath an unsupported shed and cause it to subside further still.
Timber skids vs paving slabs vs concrete: which shed foundation should you choose?
There’s no single best answer: the right choice depends on shed size, how flat your garden already is, your budget and how permanent you want the build to be. Here’s how the three most common options compare.
Timber skid foundation: cheapest and most flexible
A skid foundation uses two or three pressure-treated timbers (typically 4×6 or 6×6 in the US, or roughly 100x150mm timbers in the UK) laid parallel on the ground. The floor frame sits directly on top of these runners. Shed Build Planner notes this is the simplest and cheapest foundation method, and it has been used for agricultural outbuildings for centuries.
Best for: small to medium sheds, sloping or awkward ground, and anyone who might want to move the shed later. Because the shed sits on runners rather than a fixed slab, you can re-level it with a jack if the ground settles, a genuine advantage.
Watch out for: untreated timber in ground contact will rot quickly, so use properly pressure-treated runners, and never lay skids directly on soil without a drainage layer beneath.
Paving slab base: the practical middle ground
Individual paving slabs laid on compacted hardcore or sand support the shed’s floor bearers at key points. They cope with a bit more ground unevenness than a rigid pour, they drain well, and they can be adjusted individually if settling occurs. As Opal Retail puts it, slabs cope with a bit more unevenness for a bit more effort than a quick-fit base.
Best for: medium sheds, flat-ish gardens, and DIYers who want something more permanent than skids without mixing concrete.
Watch out for: slabs need to sit under every floor bearer, not just the corners, or the floor will bounce and eventually sag between supports.
Concrete base: the permanent option
A poured slab is level, solid and maintenance-free, but Opal Retail is blunt about when it’s justified: poured concrete is really only worth it under a large workshop-style shed or anything holding serious weight. If you’re fitting out a proper workspace with heavy machinery (the kind of kit you’d store in something like a ToughSystem drawer setup described in our ToughSystem drawer replacement guide), the extra cost can be worthwhile.
Best for: large sheds, workshops, and grounds where the building is unlikely to need moving.
Watch out for: it’s permanent, it’s the most expensive option, and getting the pour level and cured properly is real work. Mistakes are expensive to fix.
How much does each shed base cost?
Exact prices vary with timber, slab and concrete costs in your region, but the relative order is consistent across UK and US sources: skids on gravel cost the least (treated timbers plus a few bags or a bulk load of gravel), paving slabs sit in the middle (slabs plus sharp sand or hardcore), and concrete is the most expensive once you factor in formwork, hardcore, cement or a ready-mix delivery, and possibly a mixer hire.
Budget rule of thumb:
- Skid foundation: the cost of two or three treated timbers plus gravel and geotextile fabric: a weekend and a modest materials bill.
- Paving slab base: slabs, sub-base material and sand; more materials than skids, but no concrete mixing.
- Concrete: the highest cost by a clear margin, plus the most labour or the cost of a ready-mix delivery for anything beyond a very small shed.
Check current prices at your local builders’ merchant before committing; timber and cement prices move around enough that quoting figures here would quickly go out of date.
How to level a shed on a timber skid foundation
Skids are the most forgiving foundation to level, which is one of their big selling points. Here’s the process, based on the method described by Garden Buildings Direct for no-dig foundations.
- Clear the site. Remove vegetation, large rocks and the top layer of sod across the footprint of the shed, per the Shed Build Planner guidance.
- Mark it out. Use string or timber to outline where your gravel bed will go, and frame the area with treated wood or landscape timbers to stop the gravel spreading.
- Lay weed control. Roll out heavy-duty geotextile fabric before adding stone. This stops weeds poking through and prevents the gravel sinking into the soil.
- Pour and compact the gravel. Use ¾-inch clean gravel or crushed stone; avoid smooth pea gravel, which doesn’t lock together. Pour it a few inches at a time and compress each layer with a hand tamper or a heavy board. Don’t skip this: a solid base starts with good compaction.
- Position the skids. Lay your pressure-treated skids on top of the gravel, parallel and spaced to match the floor bearers.
- Level across both skids. Check for level along each skid and across both together. If one end is low, slide in more gravel underneath; if it’s too high, scrape some out.
- Place the shed. With the skids level, you’re ready to set the floor frame or the shed itself on top.
The beauty of this system is that levelling is never finished forever. If the shed settles in a year’s time, you can jack up one corner and adjust the gravel beneath, something impossible with a concrete slab.
How to build a paving slab shed base
A slab base follows the same preparation as a skid foundation up to the gravel stage, then swaps the timber for slabs.
- Mark and dig out. Outline the base slightly larger than the shed footprint and remove topsoil to a depth that allows a sub-base plus sand plus slab thickness.
- Add and compact the sub-base. Hardcore or MOT Type 1 (crushed stone in the US) compacted in layers gives you a stable, free-draining platform.
- Screed a sand bed. A layer of sharp sand over the compacted sub-base lets you fine-tune each slab’s height.
- Lay the slabs under every floor bearer. Check each slab with a spirit level, both individually and across the whole base. Where the shed’s bearers will sit is where accuracy matters most.
- Brush sand into the joints if you wish to stabilise them, but the structural support comes from the fully bedded slabs, not the joints.
The main mistake to avoid is treating the slabs as decoration rather than structure. They’re the shed’s actual foundation points, so each one needs to be solidly bedded, not wobbling on loose sand.
When is a concrete shed base worth it?
Pour concrete when the shed is large, heavy or permanent. A workshop shed with a bench, heavy tools and stored materials benefits from a slab that will never shift, and the smooth floor is pleasant to work on. The trade-offs are cost, labour and permanence.
If you do pour, the fundamentals mirror the other methods: dig out and remove topsoil, build formwork to the finished size, add and compact hardcore, lay a damp-proof membrane, then pour and screed the concrete level. Give it adequate curing time before loading; rushing this stage is how slabs crack. If your project list also includes power tools and site work, our DeWalt 20V MAX tool bag buyer’s guide covers kit that earns its keep on jobs like this.
Common shed foundation mistakes to avoid
- Building straight on grass. The most common and most costly shortcut: the shed sinks and the floor rots from below.
- Skipping compaction. Loose gravel settles, and the shed goes with it. Compact in thin layers, not one thick pour.
- Using untreated timber. Skids in ground contact must be pressure-treated or they’ll rot within a few seasons.
- Ignoring drainage. A base that sits in a puddle fails regardless of material. Choose a spot where water doesn’t collect, and let the gravel or slab base shed water away from the shed.
- Not checking level diagonally. Levelling along the edges but not across the diagonals is how you end up with a twist in the floor frame and doors that won’t close.
Affiliate recommendation
Mentioned in this article: My Shed Plans
My Shed Plans is a collection of plans for building garden sheds.
Read the seller’s information →
Affiliate link: we may earn a commission if you purchase, at no extra cost to you. We have not tested this product.
FAQ
Can I put a shed directly on grass?
No. A shed on grass or bare soil sinks and twists as the ground shifts, and the timber floor bearers sit in permanently damp ground and rot from below, according to Opal Retail’s UK shed base guide. Even a well-built shed will lean, sink or rot within a couple of seasons without a proper base.
What’s the cheapest shed foundation that still works?
A timber skid foundation on a compacted gravel bed. It uses just two or three pressure-treated timbers plus gravel and geotextile fabric, needs no digging or concrete, and can be re-levelled in future by adjusting the gravel beneath the skids.
Do I need planning permission for a shed base?
In most cases a shed and its base fall under permitted development rules in the UK and shed zoning rules in the US, but rules vary by height, footprint and location, and some properties and locations are subject to additional restrictions. Check with your local planning authority before building anything large or permanent.
How level does a shed base need to be?
Very. A shed floor should be level along its length and across its width, and as flat and even as you can make it. Even a small twist causes sticky doors, gaps in the cladding and uneven floor loading. Take your time at the levelling stage; it’s the cheapest point to fix errors.
Can I put a plastic grid base on a slope?
Plastic grid bases suit small to medium sheds on reasonably flat ground and go down quickly, but on a noticeable slope they’re not the right tool. On sloping ground, a gravel-bed skid foundation or a stepped slab base is the better approach.
Choosing your shed foundation: the next step
For most hobby woodworkers and DIYers, the decision comes down to shed size and garden slope: timber skids on compacted gravel for small-to-medium sheds and awkward ground, paving slabs for a firmer semi-permanent base, and concrete reserved for large workshop buildings carrying serious weight. Whichever you pick, invest the time in site clearing, geotextile, compaction and careful levelling; that’s what separates a shed that lasts decades from one that leans within two seasons. Once the base is in and level, you’re ready to build or site your shed on it, and our guide to 3D printed battery adapters for power tools is a handy read for kitting out the new workspace afterwards.





